Accueil > Concentrates > Atomizers for concentrates > Quartz Quest - 510 - Divine Tribe - Clearomiseur pour concentrés

Quartz Quest - 510 - Divine Tribe - Clearomiseur pour concentrés

By buying this product you can collect up to 54 loyalty points. Your cart will total 54 loyalty points that can be converted into a voucher of 1,62 €.


32,50 € tax incl.

New product

The Quartz Quest from Divine Tribe is a clearomizer designed on the concept of quartz bangerz with carb cap. To screw on your Mod Ecig, like the Istick Pico 75 watt available here.


No screw 510.
Use with care.
Fully rebuildable.
Eco-Friendly design.


More details

Add to wishlist

The Quartz Quest from Divine Tribe is a clearomizer designed on the concept of quartz bangerz with carb cap.

Focntioned with temperature control mode.


No 510 screws.
Use with care.
Fully rebuildable.
Eco-Friendly design.



The Quartz Quest Cleaormizer from Divine Tribe comes with:

  • 10 cotton swabs
  • a protective silicone ring


Clearomizer compatible with the type crystal C..B...

If you need a mod / electronic cigarette for the generation 2 DC Divine Tribe we have selected the Box Istick Pico 75 watt, which is robust and very practical for this clearomizer.

As a general rule it is advisable to set its mod on:

  • Wattage 40-55w
  • TCR Value of 280 on 49w to get 260 ° C.

A lower temperature gives better flavors and smaller clouds.


By cleaning it after each use with a cotton rod (wooden body) or a piece of paper this clearomizer guarantees you one of the best flavors available on the market.

The direct competitor of PuffCo Plus.

To use the Quartz Quest here are some instructions to respect in order not to overheat your clearomizer.

Quartz Quest Mod Specification
Eleaf pico TCR -
300 using 50w to get to 500°f (pulse button after initial 10 seconds throughout the session)
Paranormal 166 -
tcr .00240
(ArcticFox on Pico)
Big hits: TCR 300 / 50w / 500 degrees F / resistance locked at .24 ohms
(ArcticFox on Pico)
Low and slow (more accurate temperature, but longer heat-ups and more firing to keep bucket at temp): TCR 225 / 45w / 520 degrees F / resistance locked at .24 ohms
(VooPoo GENE)
Big hits: TCR 4913 / 55w / 500 degrees F / resistance .26 ohms
LostVape Therion dna75c :
50 watts, r locked at room temp (0.238 for mine), Replay mode.
Fire it til the load boils + 1 to 2 seconds. Let off. "Save Puff". Subsequently (for fresh and partial loads, both) , just lay on the button til a few seconds before you're 'full'.
Works better, than any combination of settings tried.
Cuboid 200 & Vtc mini (both joyetech)
TCR 400, 60 W, 425°F, .25Ω
Requires pre-heat Imo. Excellent flavorPico
E-Leaf with Arctic Fox installed.
TCR 225, resistance locked at 0.25, 414 F temp, 55 watts.
Requires 10 - 15 seconds of warmup but then it hits like a champ for 4-5 puffs.
Voopoo drag
Tcr 4913, 50w, 450, .24 resistance
It's weird - the heaters are made of tungsten (typically TCR 450 or 4500 on GENE) but with the conversion chart it brings it to 4913

.

Even though the heater TCR is accurate, the heat value itself isn't. TCR 2350/2400 is more accurate heat value-wise, but I 'm still liking the 4913 performance way more.
Rx2 21700
TCR: 235 40w-45w 510°F-540°F












Short video presentation of the Quartz Quest clearomizer from Divine Tribe:

5 other products in the same category: